Service
distribution board mounting
(.../IVS) 1
Front IP30
Fitting dimensions according to DIN 43880
For snap fitting to
EN 50022 top-hat rail
Space requirement
P1, 3-pole: 3 space units
P3, 3-pole: 4 space units
P3-.../IVS can be locked in
0 (Off) position using the padlocking
feature |
Rear mounting
(.../Z) 2
Front IP65
Secured by snap fitting or screw fixing
For snap fitting to EN 50022 top-hat rail
Coupling drive in door or cover
Connection from the front
2 add-on modules can be fitted (also
retrofitted)
Rear mounting main switches
(.../V/SVB) 2
Front IP65
According to IEC/EN 60204 and
IEC/EN 60947-3
With door interlock in the I position
Maintenance key for commissioning or
fault tracing
Lockable in 0 position with 3 padlocks
Two add-on modules can be fitted (also
retrofitted) |
Flush mounting
(.../E) 3
Front IP65
Fitting and connection from the rear
Terminal:
Pozidriv plus-minus screw
Finger- and back-of-hand proof
2 add-on modules can be fitted (also
retrofitted)
Flush mounting main switches
(.../EA/SVB) 3
Front IP65
According to IEC/EN 60204 and
IEC/EN 60947-3
N terminal and PE terminal
Lockable in 0 position with 3 padlocks
2 add-on modules can be fitted (also
retrofitted)
Centre mounting (.../EZ) 3
Front IP65
Mounting in ∅ 22.3 fixing hole
according to IEC/EN 60947-5-1
“One-man installation” through centre
fixing |
Add-on modules 4
Switched neutral
(early-make contact)
HI 11 auxiliary contact= 1 make contact +
1 break contact
Finger-proof
Auxiliary make contact:
always connected as load-shedding
contact (late-make, early-break) |
Surface mounting
(.../I...) 5
IP65
With an additional terminal
Add-on modules for retrofitting:
P1: + 1, P3: + 2
Enclosures for metric cable glands
according to EN 50262
Surface mounting main switches
(.../I...) 5
IP65
With an additional terminal
According to IEC/EN 60204 and
IEC/EN 60947-3
Lockable in 0 position with 3 padlocks
Add-on modules for retrofitting:
P1: + 1, P3: + 2
Enclosures for metric cable glands
according to EN 50262 |
Safety switches
(.../I...-SI) 6
IP65
With an additional terminal
With cover fuse in the 0 position
Lockable in 0 position with 3 padlocks
With “Safety Switch” label
Colour: orange
Enclosures for metric cable glands
according to EN 50262
in Switzerland: according to SUVA
Directive |
Main switch
(assembly kit)
for use as Emergency-Stop device 7
According to IEC/EN 60204-1
With red rotary handle and yellow locking
collar
Lockable in 0 position |
Main switch
(assembly kit) 8
Black rotary handle and locking collar
Lockable in the 0 (Off) position |
Thumb-grip for use
as
Emergency-Stop device
9
According to IEC/EN 60204-1
Red thumb-grip with yellow front plate |
Thumb-grip 10
Black thumb-grip with front plate |
Coupling drive 11
Includes push-fit shaft
For retrofitting T0(T3)-.../XZ basic
switches for rear mounting
Spare parts for T0(T3)/(P1)-.../Z
For retrofit conversion of T5(B)-.../E
flush mounting switches for rear mounting
Spare part for T5(B)-.../Z |
|
